Atlantis Land A02-WAP-54G Uživatelský manuál

i I-Fly Wireless Access Point User’s Manual (V1.0)

Chapiter 3 Configuration The I-Fly Wireless Access Point can be configured with your Web browser. The web browser is included as a standard applicati

7 3.3 Test TCP/IP After configuring the TCP/IP protocol, you can use the ping command to check if your computer has successfully connected to this AP

3.5 Factory Default Settings Before configurating this AP, you need to know the following default settings. Web Configurator Username : ad

9 The below window will popup. Please enter the user name and password. Both of the default is “admin”. Now, the main menu screen is popup.

At the configuration homepage (if Quick Setup Wizard starts, please close it or read the printed Quick Start Guide), the left navigation page where bo

11 • Wireless: Shows the Mac address, current ESSID, the status of Encryption Function (Enable or Disable), the current using channel. The current w

• AP Name: The name of the AP, which can be used to identify the Access Point among the all the Access Points in the wireless network. • SSID: Servi

13 3.7.3 IP Settings This page allows you to configure the IP and DHCP settings of the Access Point. The default IP address of this access point is

3.7.4 Advanced Setting This page contains configurations for advanced users, which the change reflects the wireless performance and operating modes.

15 2 AP Client: Acts as an Ethernet-to-Wireless Bridge, which allows a LAN or a single computer station (no driver installation is need) to join a

COPYRIGHT The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other names mentioned mat be trademarks or registered trademark

3 Wireless Bridge: A pair of APs operating under Bridge mode to act as the bridge that connect two Ethernet networks or Ethernet enabled clients tog

17 5 Repeat Mode: It is able to extend the effective range and coverage of the wireless network. Please make sure the SSID is the same as that AP you

‘SuperG based’ product is available. If no, the connection is via ‘normal’ G. Static turbo means it will not go back to ‘normal’ G once it starts • A

19 MAC Filter: MAC Filter function controls the MAC of the network devices that are listed in this table for access authorization or denial. When

• Enable 802.1x security by selecting “Enable”. • If MD5 EAP method is used then you can skip step 2 and go to step 3. • Select the Encryption

21 3.7.7.1 (Save/Load)Settings • Backup Settings: Click on “Backup” button, which will open a FileSave Dialog box, where you get to save all the c

3.8 Configuration through AP Utility (Optional) Launch Setup.exe (CDRom:\Utility\setup.exe) to install tha AP Utility. 3.8.1 Link Info

23

3.8.2 AP Settings Basic Setting: • ESSID: It is used by all wireless devices within the wireless network. • Channel: Select the appropriate chann

25 • Repeat Mode:It is able to extend the effective range and coverage of the wireless network. Please make sure the SSID is the same as that AP you

INDEX CHAPITER 1... 1 1.1 AN OVERVIEW OF T

indicates the combination of two channels to enhance the throughput. Super G without turbo indicates that it is on Super G mode without the channel’s

27 3.8.4 Security • Data Encryption: please tick it if you like to have WEP key as the encryption mechanism. • Authentication Mode: The authentic

3.8.5 802.1X Settings There are three essential components to the 802.1x infrastructure: (1) Supplicant, (2) Authenticator and (3) Server. The Acces

29 If users like to set 802.1X or the authentication type is set to WPA, please enable 802.1X function by ticking it. • Encryption Key: Select the

30 APPENDIX A Super G SuperG™ is an assemble of solutions that are Atheros® properties .They allow you to obtain performances far superior

31 Maximum theoretical limits* Standard Channel Modulation Max Link-Rate Max Throughput(TCP) Max Throughput(UDP)802.11b 3 CCK 11Mbps 5.9 Mbp

APPENDIX B Technical Features Physical Interfaces LAN: 1 RJ45 10/100 Base-TX Fast Ethernet Wireless 54Mbps (IEEE802.11g) and 11Mbps (IEEE802.11b) 3

33 Physical and Environmental Power Consumation: (5V ± 5%, 2.4A AC Adapter) Dimensions: 145mm*110mm*35mm Weight: 350g Temperature: Operating:[0°C to

APPENDIX C Glossary Access Point An interview networking device that seamlessly connects wired and wireless networks Authentication Authenticati

35 FTP FTP (File Transfer Protocol) is used to transfer files over a TCP/IP network, and is typically used for transferring large files or uploadin

APPENDIX B... 32 TECHNICAL FEATURES...

MTU MTU (Maximum Transmission/Transfer Unit) is the largest packet size that can be sent over a network. Messages larger than the MTU are divided into

37 RTS RTS (Request To Send) is a signal sent from the transmitting station to the receiving station requesting permission to transmit data. Serv

38 APPENDIX D Support If you have any problems with the Wireless AP, please consult this manual. If you continue to have problems you should contact t

1 Chapiter 1 Introduction And' besides available on CDRom a Quick Start Guide for a fast configuration. 1.1 An Overview of the I-Fly Wireless Ac

1.3 I-Fly Wireless Access Point Features I-Fly Wireless Access Point provides the following features: • Interoperable with IEEE802.11g and IEEE802.1

3 ● Enables remote access to corporate network information, for example e-mail and the company home page

4 Chapiter 2 Using I-Fly Wireless Access Point 2.1 Cautions for using the I-Fly Wireless Access Point Do not place the AP under high humidity and hi

5 2.4 Cabling The most common problem is bad cabling. Make sure that all connected devices are turned on. On the front of the product is a bank of LE